Click here to make us your homepage

Bookmark V6FBody

ATTENTION SPONSORS ADVERTISE WITH US CLICK HERE FOR DETAILS

V6FBody Online's - Techbase

2nd Generation FAQ: Exterior Related

What were the dimensions of the Camaro's?
What Camaro's got split bumpers?
What years did the Camaro have a hood scoop and was it functional?
What years did the Firebird have a hood scoop and was it functional?
How can I adjust my leaking (rain and wind) T-top?

 
 
What were the dimensions of the Camaro's?

The following are in inches:

 
    1970 1/2
       Wheelbase:     108.0
       Width:          74.4
       Height:         50.1
       Weight:         3313
 
    1971
       Wheelbase:     108.0
       Width:          74.4
       Height:         50.5
       Weight:         3313
 
    1972
       Wheelbase:     108.0
       Width:          74.4
       Height:         50.5
       Weight:         3310
 
    1973
       Wheelbase:     108.0
       Width:          74.4
       Height:         49.1
       Weight:         3354
 
    1974
       Wheelbase:     108.0
       Width:          74.4
       Height:         49.1
       Weight:         3627
 
    1975
       Wheelbase:     108.0
       Width:          74.4
       Height:         49.1
       Weight:         3723
 
    1976
       Wheelbase:     108.0
       Width:          74.4
       Height:         49.1
       Weight:         3679
 
    1977
       Wheelbase:     108.0
       Width:          74.4
       Height:         49.1
       Weight:         3663
 
    1978
       Wheelbase:     108.0
       Width:          74.4
       Height:         49.1
       Weight:         3612
 
    1979
       Wheelbase:     108.0
       Width:          74.5
       Height:         49.2
       Weight:         3612
 
    1980
       Wheelbase:     108.0
       Width:          74.5
       Height:         49.2
       Weight:         3545
Back To Top
 
 
What Camaro's got split bumpers?

All Rally Sport (RS) models got them through 1973. The RS could have been combined with either the Z28 or SS options as well, meaning those cars could have split bumpers as well.

Back To Top
 

 
What years did the Camaro have a hood scoop and was it functional?

The Z28s had hood scoops from 1978 through 1981. But in '78 and '79, it was not functional. It was bolted to the flat hood with the simulated opening facing forward. However, in '80 and '81, it was functional. The induction piece is a bolt-on piece that starts out narrow at the front of the hood (about 4 - 6 inches wide) and ends up about 6 inches from the rear edge of the hood (12-14 inches wide). At the rear of this induction unit is a door which is opened by a solenoid when the car is at or near wide open throttle. The air cleaner uses the stock lower portion, but the lid is the same diameter as the filter. A rubber gasket/seal is attached to the top edge of the lower portion of the air cleaner and seals against the hood when the hood is closed.

Back To Top
 

 
What years did the Firebird have a hood scoop and was it functional?

The Formulas and Trans Am had hood scoops from 1970 through 1981. In 1970 through 1972, it was a fiberglass Hood with raised scoops at the leading edge. It could be open or closed depending upon if the car came from the factory with the Ram Air option. If it did, it had the dual snorkel air cleaner with the rubber boots that mate to the hood. From 1973 through 1975, it was the same fiberglass hood, but the scoops were blocked on all models. In 1976, it was a steel hood with raised scoops set further back and closed on all models. From 1977 through 1981, it was the same steel hood with flattened scoops set low into the hood, and functional on some models.

Back To Top
 

 
How can I adjust my leaking (rain and wind) T-top?

On the underside of each T-top, there is a cover panel with 3 screws where the handle is. Remove it and you'll see a screw for making minor adjustments. If you need major adjustments, then on the body of the car is a screw where the top latches into (the "J" hook). Remove that screw and the plastic cover to reveal two screws on a slide plate. Loosen them and adjust the plate so it's snug (not very tight, otherwise the T-top will squeak). Put everything back together and the top should fit tight but still have a little play in it (for body flex). Make sure the gasket isn't being completely crushed as it will get out shape and leak.

Back To Top

 

This website and all content contained herein is copyrighted (C) 1996-2002.

V6FBody Online - All rights reserved. Use acknowledges Terms of Use Policy's